#611A- Quick Chop Plus

Operation of the machine is as follows:

1. Using a luminescent crayon, the operator marks a board for defects and places the board on the stops. These crayon marks will not appear on the finished material once its been processed.
2. With the push of a button the chop saw operator can select which cutting bill to use on the board. Unlike the slow ‘paddle’ measuring/defecting technique, the operator does not have to walk from one end of the board to the other to determine the board’s length.
3. The board is then released, and it drops down to the fence, inside of the Safety Cage. The pusher scans the board for length and the location of the crayon marks as it travels to the end of the board.
4. The board is then fed into the saw and cut at the optimum positions based on the data entered into the cut list.

As the board is being cut, the operator can mark the next board, place it on the stops and select the next cutting bill, so that it can be scanned immediately the instant the previous board is finished. There is very little wasted time in-between boards, maximizing production of the machine.

Customers who will benefit from the Quick Chop:

• Small to medium sized shops.
• Those who currently have operators using manually operated chop saws.
• Manufacturers of high quality wood products.
• Door and Face Frame Manufacturers
• Stair and Tread Manufacturers
• Furniture Component Manufacturers

Under normal running conditions, the Quick Chop Plus can process a quantity of (4) 8 ft. long boards per minute, assuming a maximum of 5 cuts. Corresponding Production Numbers are as follows:

• (1) Hour = 1,900 Lineal Ft.
• (8) Hour Work Day
  • Assuming (7) Working Hours = 13,000+ Lineal Ft.
• 10 Hour Work Day
  • Assuming (9) Working Hours = 17,000+ Lineal Ft.

• Power Requirements (3 Phase Required)
  • 220V = 30 Amps
  • 480V = 15 Amps
• Air Requirements
  • 1/4″ Airline = 5 SCFM @ 90 psi
• Saw Blade Cutting Capacities
  • 14″ Diameter / 1″ Bore
    • 4/4 Material = 8.5″ Wide
    • 8/4 Material = 7″ Wide
  • 18″ Diameter / 1″ Bore
    • 4/4 Material = 13″ Wide
    • 16/4 Material = 10″ Wide
• Saw Arbor Motor
  • 7.5 Hp
• Max Material Length Capacity
  • Offered in 12, 16, 20, and 24 ft Length Options
• Dust Collection
  • 1 x 4″ Dust Port
  • 400 CFM Required

Advantages over Hand Chopping:

• Increases yield of cut stock
• Higher production
• Tallies Material Automatically
• Better consistency in Chop Lengths

Advantages over Other Systems:

• Simple and quick Luminescence crayon marking is used for defects or grading
• Unique design enables operator to be marking two or more boards ahead of the board being chopped. This equals higher productivity.
• Higher yield through grade sharing
• Accuracy within +/- 0.010
• Quick Chop uses a full featured computer system, not just a keypad
• Pneumatic saw actuator is fast and delivers a smooth operation cycle for accurate and quality cuts.
• Welded one-piece steel frame allows the Quick Chop to ship set up. Installs in one afternoon

Material handling is an important concept to consider to help make machinery more efficient. Cameron Automation offers a number of different solutions, to partner with your Quick Chop, that will help the operators handle the large number of parts that will be cut on this machine.

#918A Belt Outfeeds

Cameron #918A Belt Outfeeds offer a number of different solutions and layouts to fit your needs. For a single operator work cell, a 6 ft. wide by 12 ft. long belt makes a lot of sense (Pictured above and left). While the Quick Chop is cutting, the outfeed belt is moving material away from the outfeed and in an area where an operator can organize and stack parts. A different strategy, in shops where work cells are spaced out, is to use a 24″ wide x 30 Ft. Long belt to convey material away from the Quick Chop automatically, to the next area the material needs to be. Manufactured here in our Factory in Poughkeepsie, NY, we will happily build a belt to suit your needs.

—————————————————————————————————————————————————————————–

#613A- Tilting Catch Table

The Tilting catch table is a space saving design for those shops with a limited open area for their Chop work cell. It’s designed to be managed by a single operator. The Quick Chop will cut an entire board and push it out onto the outfeed table like normal. The machine will hesitate briefly while the cylinders raise the table up to horizontal, matching the flat working height of the machine, and push the entire board out. There is space for a multiple boards to be accumulated as the machine is running, to build up an inventory that the operator will need to organize.